收藏本站
4. Board Setup
Introduction
The instructions in this chapter explain how to set up the Cyclone IV GX transceiver
starter board.
Setting Up the Board
To set up and power up the board, perform the following steps:
1. The Cyclone IV GX transceiver starter board ships with its board switches
preconfigured to support the design examples in the kit. If you suspect your board
might not be currently configured with the default settings, follow the instructions
in “Factory Default Switch Settings” on page 4–2 to return the board to its factory
settings before proceeding.
2. The transceiver starter board ships with design examples stored in the flash
memory device. Verify the USER_PGM switch (S8.2) is set to the off position to
load the design stored in the factory portion of flash memory. Figure 4–1 shows the
switch location on the Cyclone IV GX transceiver starter board.
3. Connect the DC adapter (+9 V-16 V, 33.75 W) to the DC power jack (J4) on the
FPGA board and plug the cord into a power outlet.
c Use only the supplied power supply. Power regulation circuitry on the
board can be damaged by power supplies with greater voltage.
4. Set the POWER switch (SW1) to the on position. When power is supplied to the
board, a blue LED (D12) illuminates indicating that the board has power.
The MAX II device on the board contains (among other things) a parallel flash loader
(PFL) megafunction. When the board powers up, the PFL reads a design from flash
memory and configures the FPGA. The USER_PGM switch (S8.2) controls which
design to load. When the switch is in the off position, the PFL loads the design from
the factory portion of flash memory. When the switch is in the on position, the PFL
loads the design from the user hardware 1 portion of flash memory.
1
f
The kit includes a MAX II design which contains the MAX II PFL megafunction. The
design resides in the <install
dir> \kits\cycloneIVGX_4cgx15_starter\examples\max2 directory.
When configuration is complete, the CONF DONE LED (D2) illuminates, signaling
that the Cyclone IV GX device configured successfully.
For more information about the PFL megafunction, refer to AN 386: Using the Parallel
Flash Loader with the Quartus II Software .
? March 2010
Altera Corporation
Cyclone IV GX Transceiver Starter Kit User Guide
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DK-V5-EMBD-ML507-G-J DEV KIT V5 W/ISM & EDK JAPAN
DK-V6-EMBD-G-XP1 DEV KIT EMBEDDED VIRTEX 6
DK-VIDEO-2C70N VIDEO KIT W/CYCLONE II EP2C70N
DK-VIDEO-4SGX230N VIDEO KIT STRATIX IV EP4SGX230
DKUSB-1 KIT DEV FOR MB86065
DLD101-7 IC LED DRIVER HP CONST CURR 8DFN
DLP-2232H-PSOC5 MODULE PSOC5 USB ADAPTER FT2232H
DM163014 BOARD DEMO PICDEM4 12F629,16F630
相关代理商/技术参数
DK-START-4CGX15N/P 制造商:Altera Corporation 功能描述:KIT STARTER CYCLONE IV GX TRX PROMO
DK-START-5AGXB3N 功能描述:可编程逻辑 IC 开发工具 FPGA Development Kit For 5AGXFB3H4F35C5N RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
DK-START-5AGXB3NES 功能描述:可编程逻辑 IC 开发工具 FPGA Starter Kit For 5AGXFB3H4F RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
DKTA-620 功能描述:测试配件 - 其他 DUAL TYPE K THERMOCOUPLE ADAPTER RoHS:否 制造商:Tektronix 附件类型:Soft Case 颜色:Gray 设备类型:Transit Case 产品:Accessories
DKTFM3CMA6207 制造商:AVX Corporation 功能描述:
DKTGALL-KIT 功能描述:RS/USB/JTAG/HILOKITS RoHS:否 类别:套件 >> 其它 系列:- 标准包装:1 系列:- 套件类型:照明 套件包括:各类 包装:Digi-Reel® 其它名称:ZXLGMRKIT16DKR
DKTGHILOTEST-KIT 功能描述:TESTER - ADVANCED HIGH LOW RoHS:否 类别:套件 >> 其它 系列:- 标准包装:1 系列:- 套件类型:照明 套件包括:各类 包装:Digi-Reel® 其它名称:ZXLGMRKIT16DKR
DKTGJTAG-KIT 功能描述:JTAG - EXTENDED PARALLEL RoHS:否 类别:套件 >> 其它 系列:- 标准包装:1 系列:- 套件类型:照明 套件包括:各类 包装:Digi-Reel® 其它名称:ZXLGMRKIT16DKR